Self employment provides an individual with the freedom to control their time and to determine how much money they earn. Many people have discovered this and ventured in many businesses, among them agriculture. In this sector, poultry farming has become very common. There arose the need lessen the work load for those who keep meet chicken and especially when removing the feathers. The result was the development of how to make a chicken plucker procedure.
There are many tools and equipment that are required to complete the process. Assemble them all together at the work station. Purchase and or borrow those that are not readily available from the local surroundings. Should there be any difficulty experienced while assembling them together, then a person with the desired experience is consulted. A single mistake could lead to the machines malfunctioning or even causing injuries to the users.
Since the process involves many potentially dangerous activities, it is advisable to have shielding garments for example gloves, welding glasses, an overall and so on. These will make sure that all the parts of the body are free from injuries. These shielding clothes should be put to use when using the machine to avoid stains from the feathers. A board cut to size is fit with a carpet on the sides and secured with small nails. This is where the motor is secured.
On another board make four holes that will provide support for the motor. This second board is attached to the first board made in step one. Once this has been achieved, the motor is put in place. Make sure that the piece of wood used is smooth. Remove the rough edges with a rudder or better still, use plywood.
Another smooth flat wood is cut to size and attached to the second. The corners are smoothed out at forty five degrees. Measure this very accurately. Since the motor is already fastened, put in place the electrical chest opposite the engine. The source of power, cord and switch are the joined together using a wire.
The equipment is now ready to insert the fingers. This is done from the inside towards the outside. The holes in which the fingers are put in are made close together, that is if the cap is small. They are put far apart if it is big. This is done all round and all the way to the top. Make sure that they are tightly fixed so that they do not come off during the process of plucking of the chicken.
At the middle bottom of the cover, make an opening. It should fit the rod tightly so do not have it too wide. This will provide support for the lid as it goes round. On the side of the engine is where the rod is attached firmly, preferably with the use of electricity. Use nuts to attach the cap and the rod together.
Many people have made this a source of their livelihood as these machines are on demand. They have mastered the skill of how to make a chicken plucker and made it an economic activity. However, the art is easy to learn from those who are conversant with the procedures.
There are many tools and equipment that are required to complete the process. Assemble them all together at the work station. Purchase and or borrow those that are not readily available from the local surroundings. Should there be any difficulty experienced while assembling them together, then a person with the desired experience is consulted. A single mistake could lead to the machines malfunctioning or even causing injuries to the users.
Since the process involves many potentially dangerous activities, it is advisable to have shielding garments for example gloves, welding glasses, an overall and so on. These will make sure that all the parts of the body are free from injuries. These shielding clothes should be put to use when using the machine to avoid stains from the feathers. A board cut to size is fit with a carpet on the sides and secured with small nails. This is where the motor is secured.
On another board make four holes that will provide support for the motor. This second board is attached to the first board made in step one. Once this has been achieved, the motor is put in place. Make sure that the piece of wood used is smooth. Remove the rough edges with a rudder or better still, use plywood.
Another smooth flat wood is cut to size and attached to the second. The corners are smoothed out at forty five degrees. Measure this very accurately. Since the motor is already fastened, put in place the electrical chest opposite the engine. The source of power, cord and switch are the joined together using a wire.
The equipment is now ready to insert the fingers. This is done from the inside towards the outside. The holes in which the fingers are put in are made close together, that is if the cap is small. They are put far apart if it is big. This is done all round and all the way to the top. Make sure that they are tightly fixed so that they do not come off during the process of plucking of the chicken.
At the middle bottom of the cover, make an opening. It should fit the rod tightly so do not have it too wide. This will provide support for the lid as it goes round. On the side of the engine is where the rod is attached firmly, preferably with the use of electricity. Use nuts to attach the cap and the rod together.
Many people have made this a source of their livelihood as these machines are on demand. They have mastered the skill of how to make a chicken plucker and made it an economic activity. However, the art is easy to learn from those who are conversant with the procedures.